Filter By:
Taillights

$25.00
Put this little bright spot anywhere—your belt, your backpack, your seatpost—and ride on. The Flashback is your go-to savior, packing a mighty “I’m here!” punch to keep you visible on the streets. With its belt clip, you can literally clip it on just about anything, and its compact size makes it a total no-brainer for keeping your ride safe and your street-cred high.
- Compact, bright, and waterproof.
- Built-in fabric belt clip makes it a clip-anywhere taillight option (seatpost mount included).
- Four operating modes: Steady (10 lumens), Power Flash (20 lumens), Disco Flash (14 lumens), Eco Flash (5 lumens).
- 2- to 20-hour runtime, depending on mode.
- Tested and approved for the following Specialized helmet models: Align, Ambush Comp, Chamonix, Propero II, Echelon II

$50.00
Nothing says, “see me now,” louder than a strong and bright taillight, both for day or nighttime use. With its spherical lens, which directs lumens more than a 1/2 mile (800m) in the brightest California sun, the Stix Elite taillight is the go-to taillight for our infamous Lunch Ride. It’s all about peace of mind, really, and with its six light modes, you get multiple options for day or night visibility. And depending on the chosen mode, this taillight will run for up to 77 hours, and it’s easily charged via built-in USB tab, which eliminates the need for a cable.
- 12 to 100 lumens output
- Dome lens concentrates output from CREE XBD P4 center LED for 1/2 mile (800m) visibility in the brightest sun. Fresnel lenses for secondary LEDs provide wide angle visibility
- 2.5- to 77-hour runtime
- Charges in the USB port of any laptop or phone charger in two hours (no extra cables needed)
- Flexible mounting system works with seatposts from 22.2mm up to 35mm in diameter, plus it's compatible with most seatstays (Aero strap mount available separately)
- Six operating modes: Steady High (50 lumens), Steady Low (18 lumens), Power Surge (37 lumens), Power Flash (100 lumens), Disco Flash (40 lumens), Eco Flash (12 lumens)
- Red/Green battery charge level indicator
- Additional mounting options available separately

$29.99
The PDW Kepler eBike Tail Light offers up 220 degrees of visibility. Compatible with any 6V-15V system, this light has 3 super-bright red LED's. Equipped with a pre-installed Bosch plug, the Kepler eBike Tail Light is ready to plug directly into any Bosch eBike system. The Bosch plug can also easily be clipped off for direct wiring into other eBike systems.
- Seatpost or seatstay mounting
- 220 degrees of visibility
- 25 Lumens
- 48" cable length
- Remove Bosch plug to work with any 6V-15V e-bike system

$54.99
Emax+ 150 is NiteRider's first taillight specifically made for electric bikes. It comes with a power line that's pre-wired for connection to the eBike's battery. Power line cable measures approximately 52" in length. Taillight powers ON with ignition/ power switch. Features six modes-Steady ON and varying flashes-with Built-in Mode Memory (remembers last setting).
FEATURES
- Lumen Output: 150
- 6 Modes
- Hardwired, Voltage 6 to 80 Volts DC
- Water / Dust Resistant IP64 Rated
- Weight: 75 grams
- Fits 22mm-34.9mm seat posts
- Includes a pre-wired Emax+ 150 Taillight, Seat Post Clamp Mount, Rubber Mounting Shims, and Rack Mount
LIGHT MODES
1) Fast Flash
2) Slow Flash
3) Disco Flash
4) Pulse Flash
5) High Steady
6) Low Steady
NiteRider recommends this taillight be installed by an authorized e-bike service and repair shop.

$17.95
- Compatible with 6-12V E-bike battery
- Integrated reflector
- Water and shock resistant
- Mounting distance 80 mm
- Visible from the side
- 40g

German StVZO optimized lens with wide light spread. Two high-output LEDs provide 11 lumens. IPX7 water resistant rating. Composite matrix fender mounting system. E-bike compatible (6v input, 0.6w / 12v input 1.2w) easily plugs into batteries from top makers including Bosch, Shimano and Yamaha. Stainless Allen key hardware and 130cm long power cable included.
Our e-bike lights are powered by the motor of an e-bike and need to be manually installed. Proper installation may require some disassembly of the bike and motor (depending on make and model battery type) and additional wiring to connect the light to the motor. Please contact the e-bike or motor manufacturer for installation instructions. It is highly recommended to have a trained e-bike professional install your lights for you.
- Two high-output LEDs provide 11 lumens
- StVZO optimized lens with wide light spread
- E-bike compatible 6 – 12V input, 1.25W
- Composite matrix fender-mounting system
- IPX7 water resistant
- Stainless Allen key hardware included
- 130 cm power cable included
Page 1 of 1